| G-CARRIAGE MONITOR
YARN PLYER POMPOM MAKER
CONE HOLDER
SPONGE BAR PUSHER
|
| At this page you find out about our Garter Carriage Monitor and all the other wood products that we make. Add a Sponge Bar Pusher to your order for $1.00 and save on your tools. Works for most knitting machines such as Brother, Studio, Silver Reed any machine that has a Sponge Bar.
You can contact us by phone at 218-238-5882 or by fax at 218-238-6079 or by e-mail cknitmfg@tekstar.com. You can do a buy it now on all our products on this page. You will be taken to secure locations for using your Paypal account or Credit Card.
|
|
|
SPONGE BAR PUSHER
The Sponge Bar Pusher, will save on your latch tool, or other tool you may use to push the Sponge Bar out. I have one at every knitting machine and my tool box has a couple of them for only a $1.00 you will save on your tools.
|
|
| G-CARRIAGE MONITOR
The G-Carriage Monitor is attached to the Knitting Table. It has adjustable stops on a long shaft. When the directional switch on the G-Carriage touches the adjustable stop (see picture, left click will make the picture larger), the G-Carriage returns back to knitting thus eliminating unnecessary travel beyond the knitting. There are directions on how you can have needles in A position without removing them from the machine. Leave a needle out of work for a fold line, use the G-Carriage Monitor to shape a neckline. You can knit a rope by using only 4 sts and still use the Monitor to save you hours of knitting time. This will help save on the life of the motor and moving parts of the Garter Carriage. No changes are made to the Garter Carriage.
|
G-CARRIAGE MONITOR BRACKETS
Included with the G-Carriage Monitor is a Set of Brackets either Angle or Flat (pictured with Flat Brackets). The Long Shaft, the plastic stops and the c-clamps. Good directions for setting up the Monitor and a Blooklet written by Elaine Cater on many ideas for having needles in A Position. The Monitor works with any Brother or KnitKing Machine and Garter Carriage. It will not harm your Garter Carriage.
Please state when ordering which set of Brackets you would like. You can order an extra set of Brackets at any time for $27.95.
Angle Brackets are used when having the Ribber attached to your machine or if you should use you Garter Carriage with your machine mounted on a Motor Drive unit.
Shipping is not included in the prices.
|
|
|
| YARN PLYER
Our Yarn Plyer is designed to be set up on the back side of your knitting table. It consists of two miniature tables with hollow tubes to set yarn cones over and to pull yarn string through. The unit on the floor has a vertical dowel in the center of it's table. This system virturally eliminates catching, tangling and cones tipping over. As can be seen in the picture, the yarn plies together as it unwinds from the cones. This unit does a very effective job of plying two or three strands of yarn together. The Guide and C-Clamp are also included along with very good directions for setting up.
|
CONE HOLDER
Our Cone Holder is used to keep cones of yarn from tipping over while knitting. It provides a smooth flow of yarn from the cone to the knitting machine. A high density fiberboard type material is used for the construction of the base and a 1/2" x 9" dowel is used for cone support. When ordering you will 2 cone holders for $8.00.
|
|
|
| POMPOM MAKER
The Pompom Maker operates by stringing yarn from your tension unit and getting the yarn started over the dowels. Then grasp outer ends of dowels and wind until desired size pompom is reached. Tie off and cut and trim to size. Several smaller pompoms can be made at the same time by using outermost holes and then tying off in several places before cutting. Fringe is made when you cut only one end of the yarn. The Pompom Maker is constructed entirely of birch materials.
|
|